popular electronics and communication (ec) Job Interview Questions And Answers

Once the signal is coded, modulated and then sent, the receiver must demodulate the signal. This is usually done in two steps :
1. Spectrum spreading (e.g., direct sequence or frequency hopping) modulation is removed.
2. The remaining information bearing signal is demodulated by multiplying with a local reference identical in structure and synchronised with received signal.

A discrete-time signal is defined by specifying its value only at discrete times, called sampling instants. When the sampled values are quantised and encoded, a digital signal is obtained. A digital signal is obtained from the analog signal by using an analog-to-digital converter. This entire process is referred to as the conversion of signals from analog to digital form.

electronics and communication interview questions

Various types of number for network identity are as follows :
1. MSISDN ( Mobile station ISDN) Number : It is international mobile subscriber number which is normally called mobile number. It is unique worldwide.
2. MSRN ( Mobile Subscriber Routing Number) : MSRN is used during mobile terminate trunk call to provide location of mobile subscriber.
3. HON ( Hand Over Number ) : HON is used for providing information required to transfer call from one B?SC to another BSC or to another MSC.
4. ISMI ( International Mobile Subscriber Identity Number) : Purpose of ISMI is for location update and authentication.
5. TMSI ( Temporary Mobile Subscriber Identity ) : TMSI is used instead of IMSI to improve security efficiency of network.
6. IMEI : International Mobile Equipment Identity.

Here are some advantages of GSM :
1. GSM is mature, this maturity means a more stable network with robust features.
2. Less signal deterioration inside buildings.
3. Ability to use repeaters.
4. Talk time is generally higher in GSM phones due to pulse nature of transmission.
5. The availability of Subscriber Identity Modules allows users to switch networks and handset at will.
6. GSM covers virtually all parts of world so international roaming is not a problem.

To be usable for direct sequence spreading, a PN code must meet the following conditions :

1. Sequence must be built from 2 levelled numbers.
2. The codes must have sharp autocorrelation peak to enable code synchronization.
3. Codes must have a low cross-correlation value, the lower it is, more are the number of users which can be allowed in the system.
4. The codes should be “balanced” i.e. the difference between ones and zeros in code may only be 1.

1.  Wire Antennas - Short Dipole Antenna
   
2.  Microstrip Antennas - Rectangular Microstrip (Patch) Antennas
   
3.  Reflector Antennas - Corner Reflector
   
4.  Travelling Wave Antennas - Helical Antennas
   
5.  Aperture Antennas - Slot Antenna
   
6.  Other Antennas - NFC Antennas
   

GPRS services are defined to fall in one of the two categories :

- PTP ( Point to point)
- PTM ( Point to Multipoint)
Some of the GPRS services are not likely to be provided by network operators during early deployment of GPRS due in part to the phased development of standard. Market demand is another factor affecting the decision of operators regarding which services to offer first.

Building penetration : Building penetration depends on the material used for construction and architecture used. This varies building to building and is based on building construction.
Building Height Effect : The signal strength is always higher at top floor and generally floor gain height is about 2.7dB/floor which is not dependent on building construction.
Building Floor Reception : The signal isolation between floors in a multi floor building is on the average about 20dB. Within a floor of 150 * 150 feet, the propagation loss due to interior walls, depending on the wall materials is about 20 dB between the strong and the weak areas.

Advantages of CDMa are as follows :

1. Frequency diversity : Transmission is spread out over a large bandwidth due to that less affected by noise. If bandwidth is increased S/N ratio increases, which means noise will be reduced.
2. Multiplication Resistance : Chipping codes used for CDMA not only exhibit low correlation but also low autocorrelation. Hence a version of the signal that is delayed by more than one chip interval does not interfere with dominant signal as in other multipath environments.
3. Privacy : Due to spread spectrum is obtained by the use of noise like signals, where each user has a unique code, so privacy is inherent.
4. Graceful Degradation. In CDMA, more users access the system simultaneously as compared to FDMa, TDMA.

SPread spectrum has the following advantages :

1. No crosstalk interference.
2. Better voice quality/data integrity and less static noise.
3. Lowered susceptibility to multipath fading.
4. Inherent security.
5. Co-existence.
6. Longer operating distances.
7. Hard to detect.
8. Hard to intercept or demodulate.
9. Harder to jam than narrow bands.
10. Use of ranging and radar.

Walsh codes have the following drawbacks :

1. The codes do not have a single, narrow autocorrelation peak.
2. The spreading is not over the whole bandwidth; instead the energy is spread over a number of discrete frequency components.
3. Although the full sequence cross correlation is identically zero, this does not hold for a partial sequence cross correlation function. Thus advantage of using orthogonal codes is lost.
4. Orthogonality is also affected by channel properties like multi path.

Properties of the ROC for the z-Transform :
1. X(z) converges uniformly if and only if the ROC of the z-transform X(z) of the sequence includes the unit circle. The ROC of X(z) consists of a ring in the z-plane centered about the origin. That is, the ROC of the z-transform of x(n) has values of z for which x(n) r-n is absolutely summable.
2. The ROC does not contain any poles.
3. When x(n) is of finite duration then the ROC is the entire z-plane, except possibly z=0 and/or z=infinity.
4. If x(n) is a right sided sequence, the ROC will not include infinity.
5. If x(n) is a left sided sequence, the ROC will not include z=0. However if x(n)=0 for all n>0, the ROC will include z=0.
6. If x(n) is two sided and if the circle |z| = r0 is in the ROC, then the ROC will consist of a ring in the z-plane that includes the circle |z|=r0.
7. If X(z) is rational, then the ROC extends to infinity, i.e. the ROC is bounded by poles.
8. If x(n) is causal, then the ROC includes z=infinity.
9. If x(n) is anti- causal, trhen the ROC includes z=0.

electronics and communication interview questions

Some selected applications or digital signal processing that are often encountered in daily life are listed as follows:
1. Telecommunication: Echo cancellation in telephone networks.
2. Military Radar signal processing
3. Consumer electronics Digital Audio/TV
4. Instrumentation and control
5. Image processing image representation, image compression
6. Speech processing speech analysis methods are used in automatic speech recognition
7. Medicine Medical diagnostic instrumentation such as computerised tomography (CT)
8. Seismology DSP techniques are employed in geophysical exploration for oil and gas.
9. Signal Filtering Removal of unwanted background noise.

electronics and communication interview questions

Following are the parts of network management system :
1. OMC : Operation and maintenance center - Computerized monitoring center.
2. NMC : Network Management Center - Centralized control of a network is done here.
3. OSS : Operation and support system - Used for supporting activities performed in an OMC and/or NMC.

Functions of BSS are as follows :
1. Radio path control.
2. BTS and TC control.
3. Connection establishment with MS-NSS.
4. Mobility management, speech transcoding.
5. Connection of statistical data.